UCI-108 2.0.0 available

With pride we announce the availability of release 2.0.0 of the UCI-108 firmware.

The highlight of this release is the addition of a new mode to allow transparent communication between a Modbus RTU Master and its remote Modbus RTU Slaves over the same BPM fieldbus used by the Tank Management application.

The UCI-108 is a multi purpose Bi-Phase Mark (BPM) communication interface supporting the Enraf GPU/Flexconn protocol.

The UCI-108 is the most flexible solution in the tank gauging industry to create, extend and improve the quality of the BPM fieldbuses.

More information can be found on the special UCI-108 page.

UCI-108 available

With pride we announce the availability of our new product the UCI-108.

The UCI-108 is a multi purpose Bi-Phase Mark (BPM) communication interface supporting the Enraf GPU/Flexconn protocol.

The UCI-108 is the most flexible solution in the tank gauging industry to create, extend and improve the quality of the BPM fieldbuses.

More information can be found on the special UCI-108 page.

X59T available

With pride we announce the availability of our new product the X59T-LT.

The X59T-LT Tank Thermometer Interface is a special version of the X62T-VT. The interface is suitable for connection of the Honeywell-Enraf VITO LT MTT thermocouple temperature probe. The main difference is the X62T-VT supports both the 9 or 16 spots MTT probes and the X59T-LT is limited to the 9 spot versions only and at an attractive price level.

More information can be found on the special X59T page.

ISO 9001:2015

Exalon Delft's quality system ISO 9001:2015 certificate has been extended by DEKRA Certification. See our ISO 9001:2015 page.

X62T-HART upgrade available

We have upgraded the X62T-HART. The X62T connects your installed tank thermometers to various Tank Gauges with support for HART® transmitters.

Highlights of this new release:

• HART 7.7 Conformity
• Support for VITO LT probes.
• Support for more RTD probes.

More information can be found on the special X62T-HART Tank Thermometer Interface page.

HPAL 2.6 released

A new release of HPAL our HART Device Protocol Stack implementation is avaliable. Highlights of this new release:

• HART 7.7 conformity (FCG TS20013 Revision 7.7).
• Support Command 534: Read Device Variable Command Code
• New STM32 example to show how Low Layer APIs (LL) can be used.

For more information see our HPAL page.

HART Test Bench 1.6 released

Version 1.6 of the HART Test Bench has been released. The main highlights of this release:

• Conform to the latest specifications Test-1 rev 5.0, Test-3 rev 5.0 and Test-4 rev 6.1.
• New tests.

More information can be found on the special HART Test Bench page.

X62T-NMT upgrade available

We have upgraded the X62T-NMT. The X62T-NMT emulates an Endress+Hauser Prothermo NMT539 so it can operate with an Endress+Hauser level gauge.

Highlights of this new release:

• Support for MTT/VITO LT probes.
• Support for RTD probes.

More information can be found on the special X62T-NMT Tank Thermometer Interface page.

ATEX

Exalon Delft's ATEX Notification has been extended by DEKRA Certification.

The scope of our QAN/QAR for explosion safe products has been expanded from Ex i (intrinsic safety) to include Ex e (increased safety) and Ex t (dust protection). See our ATEX page.

X62T-VR available

Our latest X62T variant is a special version of the X62T-HART. The main difference is that the HART communication has been made compatible with the Honeywell-Enraf 762 VITO MRT protocol.

This way you can replace a defective Honeywell-Enraf 762 VITO MRT by a modern X62T-VR with minimal effort.

More information can be found on the special X62T-VR Tank Thermometer Interface page.